![]() After enabling NLB, the RAConfigTask runs and configures the machine with NLB settings. You should wait two minutes after completing the previous steps before proceeding. Use this procedure to add EDGE2 to the NLB cluster. In the Enable Load Balancing Wizard, click Close. On the Enable Load Balancing dialog box, click Close. In the IPv6 address box, type 2001:db8:1::10 and in the Subnet prefix length, verify the value is 64. In the IPv4 address box, type 10.0.0.10 and in the Subnet mask box, verify the subnet prefix is 255.255.255.0. On the Internal Dedicated IP Addresses page, do the following, and then click Next: On the External Dedicated IP Addresses page, in the IPv4 address box, type 131.107.0.10, in the Subnet mask box, verify the subnet prefix is 255.255.255.0, and then click Next. On the Load Balancing Method page, click Use Windows Network Load Balancing (NLB), and then click Next. In the Enable Load Balancing Wizard, click Next. ![]() ![]() In the Remote Access Management console, in the left pane, click Configuration, and then in the Tasks pane, click Enable Load Balancing. If the User Account Control dialog box appears, confirm that the action it displays is what you want, and then click Yes. On EDGE1, click Start, type RAMgmtUI.exe, and then press ENTER. Use this procedure to enable load balancing and configure the new DIPs on EDGE1. On the Installation progress dialog, verify that the installation was successful, and then click Close. On the Select features dialog, select Network Load Balancing, click Add Features, click Next, and then click Install. On EDGE1, in the Server Manager console, in the Dashboard, click Add roles and features.Ĭlick Next four times to get to the server feature selection screen. To configure EDGE1 and EDGE2 in a cluster, you must install the Network Load Balancing feature on both EDGE1 and EDGE2. Install the Network Load Balancing feature on EDGE1 and EDGE2 Repeat this procedure from step 2 on EDGE2. In the Hardware list, click the network adapter connected to the Internet network, and then in the details pane, select the Enable spoofing of MAC addresses check box. On the Settings dialog box, in the Hardware list, click the network adapter connected to the corpnet network, and then in the details pane, select the Enable spoofing of MAC addresses check box. On the machine hosting your virtual machines, in Hyper-V Manager, right-click EDGE1, and then click Settings. Perform a graceful shutdown on EDGE1 and EDGE2. Enable MAC address spoofing on EDGE1 and EDGE2 If you are creating this test lab on virtual machines, you must enable MAC address spoofing on EDGE1 and EDGE2. After enabling load balancing, you can now add EDGE2 to the cluster to provide load balancing and high availability for DirectAccess client connections. The previous DIPs on EDGE1 are automatically configured as virtual IP addresses (VIPs) for the cluster. To enable load balancing, you configure new external and internal dedicated IP addresses (DIPs) for EDGE1. EDGE1 was originally installed in single server mode. Before enabling load balancing, you must install the Network Load Balancing feature on both EDGE1 and EDGE2.Įnable load balancing on EDGE1. Install the Network Load Balancing feature on EDGE1 and EDGE2. The following procedures enable you to create and test a Remote Access cluster: Remote Access clusters provide high availability and load balancing of connections from DirectAccess clients to the internal network. When using Network Load Balancing (NLB) there is support for up to 8 Remote Access members in a single cluster. A cluster acts as a single logical server and provides centralized configuration and management for the servers in the cluster. Windows Server 2016, Windows Server 2012 R2 and Windows Server 2012 enable you to create clusters of Remote Access servers. Applies to: Windows Server 2022, Windows Server 2019, Windows Server 2016
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |